PCB assembly cost calculator estimating per board assembly and test cost at Kilandu

PCB Assembly Cost Calculator

Estimate assembly and test cost per board from placement count, pin count, part count and order quantity - before you send a BOM.

On most turnkey quotations, assembly and test are the smallest of the three big lines — components and the bare board are usually larger. This estimator works out that assembly share per board from four numbers you can read off your BOM, using the rate bands published further down this page. It runs in the browser; nothing is submitted.

PCB assembly cost estimator
Assembly and test only. Components, bare board, enclosure and freight are quoted separately.
$0.00
estimated assembly cost per board
  • SMT placement$0.00
  • Through-hole soldering$0.00
  • Test, per board$0.00
  • Setup and tooling, spread over the order$0.00
One-time items for this order: $0.00
Total assembly cost for 500 boards: $0.00
Indicative figure at the rate bands set out below, not a quotation. A firm price follows a BOM, Gerber and pick-and-place review.
Send your file set for a firm quote

What the estimator includes, and what it deliberately leaves out

The number it returns covers the labour and tooling tied to putting parts on the board and proving the board works: solder-paste printing, placement, reflow, through-hole soldering, the setup that has to happen before the first good board comes off the line, and the test coverage you select.

Four costs are excluded because they are driven by things this calculator cannot see:

  • Components. Usually the largest line in a turnkey quotation, and the one that moves most with the market. It cannot be estimated from a placement count — a board with 180 parts can carry $6 or $160 of material.
  • Bare board fabrication. Driven by layer count, material, copper weight, surface finish and panel utilisation. Quoted from the Gerber data, separately from assembly.
  • Enclosure, cable assemblies and box build. Mechanical work has its own labour model and its own tooling.
  • Conformal coating, potting and other secondary processes. Priced per board but depend on masked area and cure time, not on part count.

Because of the first two, the figure on the right is smaller than the unit price you will eventually see on a quotation. That is expected. It is the part of the quotation that this page can defend from four numbers, and nothing more.

The four inputs that move an assembly price

SMT placements

Placement is the most predictable element in the whole quotation: a machine puts a known number of parts on a known number of boards, and the cost per placement is stable across a wide range of board types. Doubling the placement count roughly doubles this line, which is why a dense control board and a sparse power board of the same size can differ by a factor of three in assembly cost.

Read the count from the pick-and-place file or the assembly drawing, not from a guess. If you only have a BOM, a working estimate is the total quantity of surface-mount lines, remembering that each reference designator is one placement.

Through-hole pins

Hand soldering is priced per pin, and at roughly four times the cost of a machine placement per joint, it adds up faster than buyers expect. A board with 100 through-hole pins carries more soldering labour than one with 300 placements. Wave or selective soldering brings the per-pin cost down, but the pin count still drives it.

The common mistake is to count connectors instead of pins: a single 2 × 20 header is 40 pins, not one component.

Unique part numbers

Every distinct part number needs a feeder position, a reel or tray, a line check against the approved vendor list, and a first-article verification. That work happens once per order, not once per board, so it is carried in the one-time column and spread across the quantity you enter. This is why the same board gets cheaper per unit as the order grows, and why a 45-line BOM costs more to set up than a 20-line BOM even when the placement count is identical.

Quantity

Quantity does not change the labour per board much. It changes how much of the fixed setup each board has to carry. At 100 pieces the setup can dominate the unit price; by 2,000 pieces it is a rounding error. If a quotation looks unreasonable at low volume, check the one-time line before assuming the per-board rate is wrong.

Sides and test coverage

A double-sided board needs two print-and-place passes, two stencils and two setups. It is not twice the price, but it is materially more than single-sided. Test coverage is priced per board plus a fixture: functional test needs a fixture built for your board, and in-circuit test needs a more expensive one with a bed of nails.

The rate bands behind the estimate

These are the planning bands this model runs on. They are generic rates for small-to-medium volume assembly in Shenzhen, reviewed periodically, and they are published here so the arithmetic is not a black box.

Cost elementUnitRate used (USD)Basis
SMT placementper placement0.0030Per machine-placed reference designator
Through-hole solderingper pin0.0120Hand or selective, including inspection
Feeder and line setupper unique part1.20One-time per order
SMT line setupper side195One-time per order; programming and first article
Stencilper side55One-time, laser-cut stainless
Functional testper board0.55Plus a fixture at 280 one-time
In-circuit testper board0.50Plus a fixture at 720 one-time

The estimator applies these rates and shows the result as a single figure. A real quotation will land somewhere within about ±20% of it, and the section below explains what pushes a specific programme to either edge.

Worked example: a 120 × 80 mm industrial control board

A four-layer control board with 180 surface-mount placements, 60 through-hole pins, 45 unique part numbers, functional test, single-sided, at 500 pieces.

  • Placement: 180 × 0.0030 = $0.54 per board
  • Through-hole: 60 × 0.0120 = $0.72 per board
  • Functional test: $0.55 per board
  • One-time: line setup and stencil $250, feeder setup 45 × 1.20 = $54, test fixture $280 → $584
  • Setup carried per board at 500 pieces: 584 ÷ 500 = $1.17
  • Assembly and test: $2.98 per board, $1,490 for the order

At 100 pieces the same board carries $5.84 of setup per unit and lands at $7.65. At 2,000 pieces it carries $0.29 and lands at $2.10. The rate per placement never changed; only the divisor did.

Why board size changes the board price more than the assembly price

Buyers often expect assembly cost to track board area. It tracks part count instead. A 200 × 150 mm power board with 90 placements and a handful of large through-hole parts can cost less to assemble than a 60 × 40 mm sensor board with 300 placements and a 0.4 mm-pitch BGA.

Area does matter — but mostly upstream, in fabrication, where panel utilisation decides how many boards fit on a panel and therefore what each one costs. Assembly notices area mainly through handling and panelisation: an odd shape or a board under about 50 mm on one side usually needs a frame or a panel to run through the line, and that adds a tooling item.

Where a firm quotation differs from an estimate

Five things move a real quotation away from the model above, in both directions:

  • Fine-pitch and BGA work. 0.4 mm pitch, CSP and BGA packages need X-ray verification and tighter process control. Placement cost rises; inspection cost rises more.
  • Component market movement. Allocation on a single part can change the whole board's price between one quotation and the next. This is why a quotation carries a validity date.
  • Test depth. A functional test that needs a custom load, a programmed harness or burn-in is not covered by a per-board rate.
  • Panelisation and tooling. A dedicated fixture, a solder pallet or a carrier adds one-time cost that small orders carry heavily.
  • Documentation and traceability requirements. Lot-level material records, first-article reports and process records are engineering time, and they are priced as such.

From estimate to firm quotation

A firm price needs four things: the BOM with manufacturer part numbers, the Gerber data, the pick-and-place file, and the quantity you actually intend to order. With those, a quotation is normally issued within one working day and covers components, fabrication, assembly, test and one-time items as separate lines, so you can see which part of the price you are arguing with.

Prototype quantities run in 5–8 working days. Repeat orders run in 2–3 weeks, and volume production in 2–5 weeks, counted from material release rather than from order date. Where a long-lead component sits on the BOM, that is stated in the quotation instead of being discovered later.

Send the file set to alden@kilandu.com, or use the quote requirements page to check what we need. If you want the reasoning behind the numbers before you send anything, the PCBA cost breakdown walks through each element of a turnkey price in more detail.

How accurate is a PCB assembly cost calculator?

It is an order-of-magnitude estimate, accurate to roughly plus or minus 20 percent for a conventional SMT and through-hole board. It cannot see fine-pitch or BGA content, test depth, panelisation or component allocation, which are the four things that move a firm quotation most.

Why is the estimate lower than the quotation I received?

Because the calculator covers assembly and test only. Components and bare board fabrication are usually the larger part of a turnkey PCBA price and are quoted from the BOM and Gerber data, not from a part count.

Does board size affect PCB assembly cost?

Less than most buyers expect. Assembly tracks part count; board area mostly drives fabrication, where panel utilisation decides how many boards fit on a panel. Area reaches assembly mainly through handling and panelisation of very small or irregular boards.

What is the minimum quantity for a PCBA order?

Quantity is set per programme rather than by a fixed floor, because the one-time items - stencils, line setup, fixtures - are what make small orders expensive. The estimator shows these as a separate line so the effect of quantity is visible.

What files do you need to give a firm assembly price?

The BOM with manufacturer part numbers, the Gerber data, the pick-and-place file and the intended order quantity. With those a quotation is normally issued within one working day, with components, fabrication, assembly and test priced as separate lines.